An arrow rest might be the most vital attachment you can install for your bow. Your rest guarantees steady arrow flight and aids in the stacking of tight groups into the target.
Nevertheless, recurve arrow rests are also one of the things that can be challenging to install right. I will be shining some light on a 2 method guide on how to install an arrow rest on a recurve bow.
But before you proceed, you may want to check the best arrow rest in the market this year.
Installing a Stick-On Arrow Rest
These are excellent tiny rests that are simple to change and dependable enough for any skill set. In fact, certain Olympic archers also use this form of rest. This type of rest is easy to install; below is a step-by-step guide on how to do it:
Step 1: Keep the Table Clean
You should clean your workspace before starting the project. Look for filth and dust and thoroughly clean. If there are any unneeded items on the table, get rid of them right away.
After that, gently polish the arrow risers’ body. Search for dirt in that area and then clean it up. You may use a dishwashing liquid in this situation. Perform it gently because you’ll put yourself in jeopardy of future problems if you don’t do it carefully.
Step 2: Trim Your Arrow Rest
You’ll need to trim your arrow rest if it’s too long. Your best option is to place it on the riser. You should do it as if you were going to attach it.
Afterward, with the riser still in place, draw a circle around it. Then, cut the arrow rest to your preferred size with a sharp knife.
Step 3: Remove the Self-adhesive Paper
Simply peel off the strips’ end if your arrow rest is still self-adhesive. Furthermore, if you want to glue an arrow plate, you can do so efficiently and simply with glue.
Remember to spread it to the bottom and riser of the plates to ensure that they adequately adhere to one another.
Step 4: Line the Arrow Plate with the Grip of the Bow
This is a crucial step, and you should take it slowly. Align the arrow plate with the grip of the bow. Allow 5/8-inches in-between arrow and the lower portion of the bow sight lens.
Step 5: Final Touch
Mount the arrow resting on the bow to complete the project. You can do this by gently pressing the rest on the bow for a few seconds to ensure that it is firmly connected.
Screw-In Arrow Rest Installation
Your arrow rest will slide off due to vibration. This is highly inconvenient, mainly if it occurs during a tournament. As a result, manufacturers created an arrow rest secured with a screw rather than sticky tape. (1)
This is popular among shooters since the arrow rest does not risk falling off the bow. It is not difficult to install if you have the right tools and expertise.
Step 1: Recognize the Function of the Holes
There are two holes visible from the front if you look very closely. You should attach the arrow rest in the first hole while the plunger in the second.
Step 2: Mount the Arrow Rest
Carefully align the arrow rest, and insert the screws into the riser holes of the bow firmly. Gently work your way through it, making sure it is secured.
Step 3: Look for Any Necessary Adjustments
You should allow exactly 5/8-inches of space between the lower portion of the bow’s sight lens and the arrow, much like the stick-on arrow rest.
Lastly, double-check for any additional changes. The riser bolt is the first thing you should inspect. You should adjust or tighten it according to your needs.
Test Your Arrow Rest
Almost there – further fine-tuning of the arrow rest can be accomplished through shooting some arrows.
You can take the following steps if the following occurs:
- Arrow fire is high
- This happens if your nocking point on the bowstring is too low. Move it upwards as necessary.
- Arrow fire is low
- Your nocking point is too high on the bowstring; that is why your arrow fire is low. Adjust it down if necessary.
You should never adjust the arrow rest. Instead, make all of your adjustments on the nocking point.
Expert Tips When Shooting
Here are a few pointers to help you out throughout your shooting session.
Tip 1: Check If the Bowstring is Properly Aligned
Place a bow square on the arrow rest you’ve already installed. You’ll be able to align the bowstring in this manner. Then, make a mark about 5mm above the indicated square.
You can locate the nocking point in an indicated region. Verify if the arrow is resting comfortably to ensure you’ve executed everything correctly. If it is, you are good to go; if it isn’t, look for possible issues.
Tip 2: Begin Shooting to Evaluate the Arrow Rest’s Quality
Firing some arrows will allow you to assess its quality. If the arrow flies too high, it signifies the nocking point on the bowstring is too low. In this instance, you’ll need to make an upward adjustment.
The nocking point on the bowstring, on the other hand, is overly high if the arrow travels too low. So, make a downward adjustment, and you’ll be good to go.
Please remember that adjusting the nocking point is only necessary if this type of issue arises. Avoid altering the arrow rest since it will produce a new problem.
Tip 3: Arrow Rest Install at an Archery Shop
Indeed, you can go to a local archery shop and have them attach the arrow rest on your recurve bow. This strategy isn’t mandatory; however, if you don’t feel confident enough to complete the installation on your own, you can enlist their help.
They will just charge a minimal cost, and the best part is that your bow will be safe in their hands.
Why Should You Install an Arrow Rest?
Since it’s such a tiny piece of equipment, arrow rests are frequently forgotten, but they’re one of the most crucial aspects of a bow, and they have a significant impact on the trajectory of your arrow. (2)
You can use an arrow rest to keep the arrow stable until you release it from the bowstring. If any arrow portions, like the shaft or the vanes, come into contact with the rest of the riser, the arrow’s direction of travel will be affected. Furthermore, manufacturers design the rest to retain the arrow in position while avoiding too much pressure, as this would change the arrow’s course.
So, for your first bow, you will almost certainly need to purchase an arrow rest. You won’t need an arrow rest unless you buy a conventional bow with an incorporated shelf. Since most novice bows and all Olympic recurve bows lack an included arrow rest, you’ll need to install one yourself.
You may check the video below;
References
(1) tournament – https://www.britannica.com/sports/tournament-competitive-event
(2) trajectory – https://study.com/academy/lesson/trajectory-definition-equation-quiz.html
